Several months back, there was some discussion on the TT Forum regarding big baits with a shad profile. By big, I recall guys asking for seven or eight inch baits. At the time, the only one of which I was aware was the Nate’s Baits product.

I totally forgot about the bait Triton Mike alluded to during our interview back in April of 2008. He chimed in on the discussion thread to bring us up to date on this bait and apparently, it has gone through a couple of different iterations.

Well, a few days after that thread took off, I received in the mail a sample bait from Triton Mike with a note asking me to check it out and provide some private feedback. This was shortly before our trip to El Novillo Lake in Mexico, so I took the bait down there with me to check out.

I was pretty excited about this bait mostly because it had a true, made in the garage feel to it with rough edges, cuts, etc. – like a bait that was already beat up. Honestly, how many of you have noticed that just about any hardbait seems to catch MORE fish after its received some battle scars? Well, this bait had some right out of the package and while Triton Mike was a bit embarrassed by this fact, I really appreciated it!

His Bull Shad was the first big bait I tied on at El Novillo, and it ended up being one of the last. On the retrieve, the bait has a pretty tight swimming motion – not wide like a Triple Trout which is what I expected since it’s a three piece design. About 5 casts later though, my Bull Shad fell victim to the Dragon Bushes of El Novillo. JIP and I tried to free the bait for a good ten minutes – I could see the bait under the water, but not reach it and we did not have anything on board with which to knock the bait free.

One final push with my rod tip and *snap* – not my rod, but the line finally broke from all the abrasion. The bait was lost

Well, recently one of our site advertisers had a sale and while I was browsing through the Hooked Up Tackle e-tail site to see what I could buy for 15% off, I noticed he had some of Triton Mike’s Bull Shads! I immediately ordered one and had it in time for a recent tackle testing trip with Zander out on Lake Pardee. Check out the result!

After I told Triton Mike what happened to his original bait he sent me, he mentioned he was already at work on a new version – typical. After I purchased the bait from Hooked Up Tackle, two days later, they announced they received in stock, the new version of Triton Mike’s Bull Shad – even more typical.

Regardless of which version you end up with, this bait is worth a look. I know I’m going to be throwing it this Fall for some of those Delta Striper if we manage to get out for them this year.

As a tackle reviewer, the amount of gear that shows up and accumulates on my boat over the course of several months can be overwhelming. While I try my best to go through each and every product and give it time on the water, in many cases, stuff gets discarded, sent back, or given away without ever getting wet.

Sometimes, I receive a product I’d like to test and write up but I find it’s either out of production, too difficult to source, or the details of its availability are just too fuzzy. One such product is this paddletail minnow that I found laying in a forgotten compartment within my boat. Its name? The “One’Up Shad”. That’s right, it bears a similar name to the hardbait from 3:16 Lure Company – a tidbit I found somewhat amusing.

This product showed up on my boat, and stayed there, after sharing time on the water with a very good friend of mine. This friend knows my affinity for JDM tackle AND big baits, so he brought these baits along as a “I betcha never seen these before” kind of challenge. Well, he was right, I hadn’t seen them before and my intial thought was, “oh, not another paddletail bait”, but after seeing its name, I knew I had to at least try them.

Well, before my friend departed, he left me several packages of the product, but of course, they got lost into obscurity amongst the pile of “stuff to check out” on my boat. Just recently, on a tackle testing trip to Lake Pardee with Zander, I remembered to pull them out to have a look.

Pardee is a favorite place for us to go to check out new baits for while the fishing can be very difficult due to the ultra clear water, this clarity affords us the unreal opportunity to really see what a bait is doing in the water on a full length cast. In fact, the only thing stopping us from going there more often is a complimentary VIP pass at the gate!

But back to the One’Up Shad. At first inspection, the bait is somewhat unremarkable. The colors are farily opaque and the shape of the bait is reminscent of an oversized Slug-O – remember those? The difference here, of course, is this bait has a paddletail AND a somewhat distinct joint in the middle of its body.

While distinct, this joint is no where near as thin and fragile as that of the Imakatsu Javallon. But the more I thought about it, the more I realized, this probably affords the bait a very unique swimming action.

Onto the end of the line it went aboard a Dobyns Rods 804CB paired with an Abu Revo Elite Aurora series reel. I spooled the Revo with 12lb test Toray HiClass fluorocarbon. Not necessarily an ideal combination, but amidst the Crankbait Rod wars, you have to make due with the rods you’re dealt.

After a few test pulls alongside the boat and remarking of the bait’s sinuous action, I made a cast to shore alongside some semi-submerged brush (Pardee is currently at full pool). I watched the bait and noticed the same swimming action we saw at the side of the boat, was happening on my medium paced retrieve. This bait has some moxy! Then, about two feet behind the bait, a large, dark shadow emerged and just as soon as I noticed it, it slowly sank back down into the depths.

Whoa! Whatever it was, it was BIG! This experience is typical of Lake Pardee, only this fish was darker than anything had seen previously and so dark, I could not make out any markings. Just it’s overall shape – literally as if it were a shadow.

A few casts later, it was on and I was able to pull up this healty, but significantly smaller largemouth bass.

I’m told these baits were made several years ago. I’m not certain if they are still made, or where in Japan you can or cannot find them, but if you are over there, and come across these baits, AND are into the paddletail style products, I suggest you buy as may packs as you can afford. I know I will now be guarding mine very closely

Sharing the same fishing waters with local manufacturers can lead to some unexpected surprises. The California Delta is a huge waterway, yet we often run into people we know while out on a field test.

Recently, one such chance meeting turned into an impromptu product preview when we ran into Grant Olguin of Black Dog Baits out fishing the Delta to field test some new baits. We recognized him from afar as he’s sporting a new logo’d wrap around his faithfull BassCat boat.

Grant Olguin from Black Dog Bait Company out fishing the Injection Punker on a late afternoon out on the California Delta

Grant was happy to see us and immediately looked side to side to see if anyone was looking. When he was satisfied the coast was clear, he suggested we tie our boats up together because he had some new stuff to show us!

We’re already aware of the new, injection Punkers, but this was our first chance to really get a good look at the bait side by side against the original Punker and with the Jr version at least, there is a size difference.

The new injection Punker Jr. (bottom) up against an original wood Punker Jr. (top). Note the injection version is much more streamlined. We've found it much easier to walk than the original.

Grant had on hand, an entire collection of new colors for the injection molded Punker Jr. but we failed to get a photo of the new color selection because of the next bait Grant pulled out. It was a prototype 4″ billed Shellcracker.

But what really excited us was this new 4" billed Shellcracker

Grant introduced it by acknowledging our “Year of the Crank” theme and asked us what we thought about it. Well, it didn’t take me long to grab it from Grant, tie it on and toss it out.

The bait is a floater and will be available in both a silent and rattled, injection molded body. They’re toying with the idea of some limited run wood versions as well, but the idea around the bait is to provide something smaller for those anglers who like the idea of big baits, but still cannot get their heads around the massive size of the majority of products.

The new 4" billed Shellcracker (front) up against an original sized version.

The new 4″ Shellcracker is essentially a jointed crankbait and on about my 4th cast with the bait (mounted on a Dobyns Rods 684CB) I got a hookup while slowly cranking the bait back to the boat along a weedline, but as I knelt down to lip the fish, it took one final lunge and got off the hook!

I know, I know, I should have swung him, but I was afraid of snapping the rod as it was a good three or four pound fish, and the 684CB is a pretty light rod. It was bad enough I was fishing a bait that probably weighed about one ounce on the poor thing.

So anyway, the picture opportunity was lost and I had to give the bait back to Grant as it was an early prototype. He tells us they’re still working out some final things with regards to colors, price point, and production runs but they hope to have the baits ready in time for ICAST 2009.

The 4" Cracker fishes just like a crankbait only if you retrieve it REALLY slow, it will wake across the surface in tantalizing fashion. This is one 4" option we may actually fish - especially during our Year of the Crank!

Lastly, there’s another bait he showed us but that we cannot talk about yet, but it’s safe to say this bait is a departure from what Black Dog Baits currently offers and it is quite the little number. Stay tuned for some official release news on this new bait as soon as we’re given the green light!

By far, the number one question that comes up at any event TackleTour attends these days is “Who is Ms. Casey?” Strike that. Actually, the FIRST question that’s asked of us is “WHERE is Ms. Casey?”

Original TT Girl, Ms. Jov

The TT Girl (actually TackleTour Teaser as first conceived) concept spawned from the arrival of the original Evergreen Opus-1 reel at TT HQ. You might remember that review. So unique was this reel to us, that we wanted to showcase our enthusiasm by having someone other than us “model” the product. Ms. Jov was our very first TT Girl.

Ms. Casey takes over the reigns as TT spokesmodel

A year later, along came the Opus-1 Nero. Almost the same reel, with a few refinements, and delivered in a stealthy black package. We needed to step up our game. I knew just the candidate, contacted her, and voila, Ms. Casey was welcomed into the TT fold. Though the Opus-1 Nero shoot was her first with TackleTour, her debut on the site actually came with the 2008 Holiday Gift Guide. The rest is pretty well chronicled on the main site and accompanying discussion forum.

Ms. Casey presents TackleTour’s 2008 Holiday Gift Guide

So who is Ms. Casey? Aside from being a friend of TackeTour and our primary spokesmodel, she is in fact, a professional model, a former Miss Chinatown San Francisco Pageant participant, and a regular at San Francisco Bay Area Hot Import Night events.

We intend to include Ms. Casey in more TT events

She’s a very busy girl but we’re delighted she’s a part of TackleTour and while this may not have answered all your questions, rest assured we intend to include her, and her friends, in more and more TackleTour events as time goes on.

By the end of this year, custom rod builders and customers throughout the world will lose one of the most highly regarded blanks in the industry. In a news release dated April 23, 2009, G.Loomis, long considered the industry benchmark for rods in North America, announced their decision to exit the custom rod blank business so they can focus on expanding their finished rods business globally.

It was just a few short years ago, where I was quite excited over the fact G.Loomis made the decision to re-release a small selection of their GLX blanks and was hoping they’d expand the selection someday to include the BCR blanks as well as the MBR842 (one of my absolute favorite rods in their lineup). But instead, today we find out quite the opposite is true

In the press release, Bruce Holt, executive director at G.Loomis made the following statement:

“This is a very difficult decision for all of us here at G.Loomis, especially since making custom rod blanks for steelhead anglers was how we got our start as a fishing tackle company back in the ‘80’s. While we realize there’s an avid following among custom rod makers for our blanks, the growth we’ve experienced on a worldwide basis for our finished rods – and especially our fly rods with both fly tackle dealers in the U.S. and abroad – makes this the right decision and direction for our business success in the future.”

The company has invested in upgrades to their Woodland, WA facility and in training for current staff in an effort to make improvements in all areas of the company. Holt continued in his statement by adding, “Our production plans include manufacturing custom rod blanks through the end of 2009, and then our complete focus will be on finished rods. Our efforts at the plant over the past few months and this decision to exit the custom blank business prepares us well for when the global economy rebounds.”

So where does that leave the custom rod builder and customer? St. Croix, Phenix Rods, Lamiglas, among a select few others will hopefully continue to offer their blanks to those who prefer to roll their own, but the loss of G.Loomis in this market segment will be significant. Personally, I’m more than just a little disappointed. Considering how conservative G.Loomis has remained with their finished rod designs, the custom wrapping route was the next best alternative to having a very stylish rod built on one of their blanks. Now that they are abandoning this segment, and removing this option, it may be time I abandon their product all together until they update some of their designs – at the very least, remove the foregrips on their bass rods.

Well, if in the past G.Loomis can re-release their GLX blanks, maybe at some point in the future, they’ll find the resources to back up on this decision as well and reopen the doors to the custom market. For now, it’s on to other resources.

About a month ago, I reported my on the water experience with the hollow braid to fluoro topshot technique shown to us by Dean Yoshizumi. Since that time, I’ve received a few inquiries as to other product options for this technique since the hollow braid from Toray is cost prohibitive for many.

With a bit of research, I was able to find that Izorline and Western Filament (makers of Tuf Line) also produce a hollow braid product and when I contacted them, they were more than happy to send in some spools for me to try out. Here’s my experience with these products:

Western Filament makes “Tuf Line Guide’s Choice” hollow braid and it’s available in 40lb test and up. The sizes that will interest freshwater fishermen are the 40lb (0.28mm) and 60lb (0.33mm). Unfortunately, these two sizes are very tough to find online and are probably best sourced through your local tackle shop. 80lb was all I could find online and it sells for roughly $220 a 1200 yard spool.

I was most excited about the 40lb product because of its small diameter and the potential to use it for 5 – 12 pound test as Terry Battisti asked me about after my initial blog. Well, unfortunately, the product is so thin, it’s tough to get the threading needle into it. I went so far as to try something smaller, a sewing needle, and even with that, I was unable to get through more than one inch of line before having difficulties with the needle poking through or the line fraying. I’m just not skilled enough in this technique to make it work.

Fortunately, the 60lb was much easier to work with and after a little practice, I was able to thread this stuff rather easily. For the sake of it, I tried some 0.25mm line in the 60lb hollow and threaded through about 3 feet into the hollow braid, but it pulled out with about 6 pounds of pressure on the line. I then tried 0.30mm line through about the same length into the hollow braid and this pulled out with about 10 pounds of pressure on the line. Next up was a 0.32mm line and this held good and strong, so this seems to be the lower diameter threshold for leader material in the 60lb. For those paying attention, this diameter equates to 14lb Sunline Shooter. The other two lines were 8lb and 10lb Yozuri Hybrid respectively.

For the above tests, I threaded the leader line through the hollow and did not tie a nail knot. I wanted to see how well the line held without the nail not in place. Once it held without the knot, then I knew it we had a good mechanical connection between the leader material and hollow braid.

I repeated the tests with the Izorline product which is called Brutally Strong. Their website states the smallest pound test this product is available in hollow is 80lbs, but I was able to get it in 60lb. Perhaps their website is not up to date. Note that “Brutally Strong” is available down to 12lb test, but this is a solid braid (also available in 20, 30, 50, 65, and 80) – so be sure, if you see this product on the store shelves or are ordering it, to specify you want the hollow. Again, all I could find online was the 80lb product and this was available in 1200 yard spools for $160 on a quick search.

Tests yielded the same results as with the Western Filament Tuf Line Guide’s Choice though it seemed this line was easier to work with initially. However, I’ve heard that Western Filament makes the Izorline hollow braid product – I offer that as an unconfirmed bit of information.

Now a quick note about the nail knot. Someone had recommended to me that you don’t really need the nail knot and you can achieve the same results with a drop of soft bait glue. The key here is to thread the leader into at least two feet of the hollow. After getting the allowable diameters figured out above, I tried this technique and while it seemed hold, what I found was you have to be VERY careful with the soft bait glue as I had a couple of occasions where a drop or two landed on the leader material and the line broke right there on my tests. While it can be a pain to tie, I think the nail knot is the safer method.

Do you really need it? Yes, you do. What happens to the sometimes, when the line is wound back up into your reel is the hollow braid will relax and when this happens, the connection to your leader material is lost. When that’s gone, your leader will pull out with very little effort. The nail knot tied right at the end of the hollow braid prevents the braid from relaxing and sliding down the leader.

At least this is the case when trying to use as low diameter as possible with the hollow braid. Things are probably different with a much thicker leader material hence the popularity of using a 20lb fluorocarbon leader instead.

So, bottom line is there are some alternatives out there though they may be a little difficult to source. According to their website, the Izorline product is available in 50, 100, 300, 500, 750 yard spools and up. Likewise, the Tuf Line Guide’s Choice comes in 150, 300, 1200 and 2500 yard spools, so if you can find a store from which to order either product, there could be some cost savings to be had.

For now, I have each product spooled up on two different Daiwa Steez 103HL reels with that 14lb Sunline Shooter leader and hope to get some on the water time with each before long.

D&M Custom Baits has released their Piranha Swim Jigs, the secret bait of Larry Hemphill, Northern California Bass Fishing Guide. Larry has been slaying fish for the last two years on this bait.

Bama Bug

Black and Blue

Product Spec’s:
3 standard sizes, 3/8 oz, 1/2 oz, 3/4 oz.
A dozen standard colors : custom colors on request.
5/0 Gamakatsu Hook
Big 3-D eyes
Head design has barb and collar.
Comes complete with skirts and matching plastic trailer.

Chartreuse Shad

Available Now at: http://www.outdoorproshop.com/D-M-Custom-Baits-s/615.htm?Click=592

Purple Passion

Rainbow Trout

D&M Custom Baits out of Northern California has released their new, custom buzzbait fresh off of a successful fall season of testing. Their new Delta Hammerhead Buzzbait comes in two configurations:

Chartreuse White

A 3/8 oz. version made of “TIN” that gives the bait a really slow speed with the great bubble trail, soft squeal and a loud Ringing head banger. This bait is available with a “Black Head only”

Black Red Flash

A 1/2 oz. “LEAD” Model featuring a loud head banger as the name implies available in 4 Head Colors. This allows D&M to customize any color combo the fishermen would like. Gold, White, Chartreuse, Black.

Chartruese Shad

With each bait, you can adjust the amount noise you want by bending the blades arm into the head for more noise, or lifting the blade arm to allow for the high pitch squeal and nice bubble trail.

Cotton Candy

D&M’s Delta Hammerhead Buzzbait features quality components with a small profile frame allowing for greater casting distance in the high winds.
The custom head designs on these buzzers facilitates their rise to the surface. This buzzbait will also fall very slow and can be used at any depth even on the bottom or in heavy cover like trees. D and M assurs us this buzzbait will not rollover at any speed.

Golden Shiner

Other components include:
5/0 Gamakatsu Hook
Custom Blades, made heavier for louder bang.
Custom Plating, giving off higher flash.
Chrome, Citrus, Burnt Orange, Gold, Black Nickel, Hot Pink for Smallies and Spotted Bass.

Night Stalker

And as always, these baits are available in custom colors by simply contacting D&M Custom Baits Directly.

Orange Crush

Available soon at: http://www.outdoorproshop.com/D-M-Custom-Baits-s/615.htm?Click=592

Sexy Shad

White Shad

At TackleTour, we do our best to stay on top of the latest tackle trends, acquire product, fish it, and report back our findings in the form of a review.

The Spro BBZ-1 Shad was introduced to us in May of 2008

Almost a year ago in May, we got our first look at Bill Siementel’s latest bait, the Spro, 4″ BBZ-1 Shad. We were pretty excited about this compact little bait that featured a big bait swagger.

The Spro BBZ-1 Shad is available in three ROF’s – Floating, Slow Sinking, Fast Sinking

Then a couple of months later in July, just before ICAST, we found out about a similarly sized product from TruTungsten that featured their innovative adjustable weight system, the 4″ Tru-Life swimbait.

The Tru-Tungsten Tru-Life 4″ bait features the same adjustable weight system and two hooks per bait.

Can you say shootout?

I was more than prepared for a full blown shootout

In the Fall of 2008, Reaction Strike got in touch with us with their interpretation of this same concept and once again, it was game on in the “swimbait” market.

We were made aware of the Reaction Strike product during the fall of 2008

I’ve gone back and forth in my mind about doing individual reviews versus a full blown shootout between these three manufacturers’ product and had pretty much decided to go full blown shootout.

The profile of these baits has garnered a lot of attention as well.

Then of course, we declared 2008 as “The Year of the Crank” on TackleTour. Normally that would not affect anything but the interesting thing I found is the more I fished cranks, the less I saw the purpose behind these little 4″ big baits.

The joints have good movement.

They all seem to share a similar issue in that unless you are retrieving them painstakingly slow, no matter their rate of fall, they will all rise in the water column. The fast sinks are better about staying down than the slow sinks, but they will all still rise if you’re not careful.

Their gill bait is even more intriguing.

Reaction Strike has a solution for this dilemma with their little big baits by offering a billed version. So then, is it still a “swimbait” or is it a crank?

And now they make one with a bill.. is it a crankbait or swimbait… a hybrid?

The term “hybrid” comes to mind… something that is a mix of two or more things but neither one or the other. You’re usually making compromises when choosing to go with something that is a hybrid.

Of the three baits, these two are most similar.

Long story short? I’m having a hard time wanting to fish these products. I’ve thrown them a few times and each time, I find myself either tying on a billed or lipless crank when wanting to stay small or tying on a traditional big bait when wanting something that “swims”.

But all three are rated at 4″

So, I’m sorry to say while I’m sure these are all worthwhile products that have their time and place, I’m just not in a proper frame of fishing mind to give them a fair shake

.

And while they catch fish, personally, I can’t bring myself to fish them enough to give them each a fair shake.

Last year’s dedication to big baits during the Swimbait Rod Wars brought about some serious lack of on the water mojo for the TackleTour crew. Sure we caught our fish, but as anyone hip to the big bait bite will attest, the droughts in between can be monumental.

We started preparing for our Year of the Crank during the fall of 2008, but the bad mojo from the Swimbait Rod Wars seemed to follow us, or at the very least, me around. On countless occasions, when invited to fish “hot” bites, we’d shut those frenzies down the second we touched the launch ramp. We couldn’t even get into the usual good striper bite in the fall.

Needless to say, prospects for the Crankbait Rod Wars were looking bleak, but we were hopeful something would materialize to change our fortunes.

Enter Leo with word of a new Lucky Swimbait Necklace made by Eddie Rodriquez of Ace Jewlery in Las Vegas. Could this charm provide the needed mojo to lift the TackleTour Jinx?

The LSN is available at Monster Tackle

We met up with Leo on Clear Lake, CA to see, but the day was not starting off well as just before Zander and Cal left TT HQ for the long, three hour drive up to Clear Lake, a skunk literally crossed the road in front of us. The bad mojo was strong this morning!

Skeet Reese and Mike Iaconelli sport the new Lucky Swimbait Necklace to finish 1, 2 at the Bassmaster Classic!

Out on the water, all three of us donned our Lucky Swimbait Necklaces, but it seemed the Bad TackleTour Mojo might just win out. Again, recent “hot bite” spots were not panning out and it seemed the TT Crew was about to squash another hopeful day on the water.

Gerald Swindle, Ish Monroe, & Jarrett Edwards are also hip to the LSN Mojo.

Then, finally, it happened … Magic hour, and in the middle of the morning, the Crankbait Rod Wars were back on track. We started hooking into fish on every second or third cast. We were official believers in the Lucky Swimbait Necklace (LSN) Mojo

Zander displays why the LSN has earned Editor’s Choice Status with the TT Crew

Later that same day, while still on the water, we caught word Brett Ehrler and Cody Meyer just finished number one and number three respectively at the FLW Lake Havasu tourney. Guess what they were wearing around their necks?

The Crankbait Rod Wars took us to Clear Lake, CA yesterday and not only did we “crank it up”, but the lake tore us up too. Zander tore something in his bicep, I lost more cranks, and Leo sacrificed his boat to get us into some pretty skinny waters.

My introduction to Blackwater International’s hollow braid topshotting technique came from fishing with Alan Fong almost a year ago when he debuted his Al-E-Baby swimbait. Alan had been shown this rigging method by Dean Yoshizumi from Blackwater International and was totally enamored with it.

I’m a natural skeptic to such things so while I was intrigued, I had to see how it was done myself before coming to any conclusions.

As fate would have it, shortly after that trip with Alan, my good friend, Jonah Li of Hi’s Tackle Box gave me a call and said there was someone he wanted me to meet. It was none other than Dean Yoshizumi.

Well, to make a long story short, Dean showed me the connection one day in Jonah’s store explaining to me it is a method he borrowed from his days of fishing long range tuna. I mean, if he can land two hundred plus tuna on such a setup, surely this rigging will hold up fishing for bass. I walked out with an armload full of product including the clamp stand so I could try this rigging method myself back home.

Unfortunately, my early attempts were not met with much success as I didn’t quite have all the pieces to the puzzle or the necessary patience to complete the rigging.

Fast forward to just last week out on El Novillo Lake in Mexico where Dean was on hand to provide top shots for everyone and I lept at the opportunity to try this once more. I had him fix up my Quantum Tour PT reel, a member of our 2009 high speed reel shootout, and off I went the next day to fish this setup on my Phenix Ultra MBX 707H rod.

Why even bother you ask? Well, if you’re one that prefers to use smaller than normal reels like me, yet, are fishing techniques that require higher strength line, AND don’t like the potential visibility issues braid presents, this is an almost perfect solution. You get the high capacity advantages of braid with the low visibility and abrasion resistance properties of fluoro.

Throw in the added benefit of no knots ticking through your guides on the cast and it is almost a no brainer!
But until you actually fish it and put this stuff through everyday applications, the trust in the connection and the benefits of going through all this trouble in the first place are rather obscure.

I’m here to share my epiphany of fishing this wicked setup:

1) Not only do you get the benefits from all of the above, but the white hollow braid makes an excellent strike indicator when floating on top of the water. You can literally see your line straighten out when fishing any slack line presentation. All that’s left for you to do is wind up the slack and set hook!

2) The abrasion resistance of the Toray Fluoro at 20lb test (we used the Bawo SuperHard Premium Plus at Novillo) is astounding. I cannot tell you how many times I cast my injection molded Lunker Punker Jr. through some of those dragon bushes and rather than move the boat in to retrieve the bait, I wound the bait up close to the bush and catapulted it back to the boat. Each time I expected my fluoro leader to be all messed up, but each time it came back as clean and unabraided as can be. I still can’t believe it.

3) Reconnecting a new leader is a snap. Dean pre-tied several fluoro to hollow braid leaders and once you have that hollow braid mainline on your reel, just use the simple, no knot hollow braid to hollow braid connection method to attach your new leader and voila, you are done. It is impossibly quick and easy.

http://tackletog.com/news/2009/03/19/hollow-braid-splice-connection/

4) You truly receive 100% line strength with this method because there are no knots to fail you. On several occasions, I snagged up on the bottom or in one of those submerged dragon bushes and could not get my bait out. No matter how hard I pulled with my thumb on the spool of the reel, I couldn’t break off. So, instead, I tied my hollow braid off at the boat cleat, well above where any of the fluorocarbon leader material was in the line and each time, I either straightened out the hooks or pulled up a section of brush.

While at Novillo, I ended up fishing this on all four of the high speed reel contestants and I used them all on techniques ranging from cranks to top water to jigs to soft plastics to big baits and I haven’t looked back since. It is now time to re-explore learning how to rig this myself because it has quickly become my favorite method of putting line on my reel.

The last thing an editor here at TackleTour needs is another space in which to write. As if my pile of product to review isn’t high enough already. But having gone through so much product in my five and a half years with TT, there are often times, follow up notes and discoveries I’ve made while continuing to use product after it has been reviewed.

Enter TackleTog… I figured I’d use my space here to post follow up comments on products that have already been reviewed and possibly even write some blurbs about products that make it to my boat, but are not intriguing enough for me to fish continually towards writing a review.

Well, that’s my intended focus anyway so we’ll see where it goes.